Commit Graph

55608 Commits

Author SHA1 Message Date
Hauke Mehrtens
95c216806b at91: Remove CONFIG_PINCTRL_MCP23S08 configuration option
The CONFIG_PINCTRL_MCP23S08 configuration option is already unset in the
generic kernel configuration.

Fixes: f938512af6 ("target/at91: replace gpio-mcp23s08 with pinctrl-mcp23s08-spi update config")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-10-31 00:46:15 +01:00
Hauke Mehrtens
d15fed98ec Revert "at91:"
This reverts commit 7cc6ffa1b9.

This should have been folded in an other commit.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-10-31 00:45:52 +01:00
Hauke Mehrtens
7cc6ffa1b9 at91:
[CONFIG_PINCTRL_MCP23S08 is already unset in generic config]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-10-30 23:37:53 +01:00
Volodymyr Puiul
3d14c610e8 ramips: add support for YunCore FAP640
It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A.

Specifications:
- SoC: MT7621AT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 16 MB SPI
- Wi-Fi:
    - MT7915DN + MT7905DAN: 2.4/5 GHz
- Ethernet: 5x1GiE via MT7530, 1xWAN with POE and 4xLAN
- UART: J4 (115200 baud)
    - Pinout: [3V3] (TXD) (RXD) (GND)
- Power: 802.11af/at PoE;

- Bootloader: U-Boot
- Buttons:
    - Reset
- LEDs:
    - Status - RGB controlled by
      - GPIO 14 LOW - green color
      - GPIO 15 LOW- red color
      - GPIO 16 LOW - blue color
    - WAN - gren color, controlled by switch GPIO 12 LOW
    - LAN1 - gren color, controlled by switch GPIO 9 HIGH
    - LAN2 - gren color, controlled by switch GPIO 6 LOW
    - LAN3 - gren color, controlled by switch GPIO 3 LOW
    - LAN4 - gren color, controlled by switch GPIO 0 LOW

Installation:
OEM firmware is based on LEDE with custom UI and support standard sysupgrade
variant of firmware. However it requires "*.ubin" extension for sysupgrade file.
Always select "Factory reset" switch on upgrade to OpenWRT, otherwise
router will not boot.

MAC addresses with OEM firmware:
vendor   source
lan      factory 0x4 (label)
5g       factory 0x4 (label)
2g       label with flipped bits bit in 1-st byte and bits 5, 6, 7 in
  4-th byte

Example
label:  44:xx:xx:b7:xx:xx
lan:    44:xx:xx:b7:xx:xx
2g      46:xx:xx:c7:xx:xx
5g      44:xx:xx:b7:xx:xx

Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
2022-10-30 23:14:45 +01:00
Csaba Sipos
cc8b8f1b41 ipq40xx: add support for MikroTik hAP ac3 LTE6 kit
This adds support for the MikroTik RouterBOARD RBD53GR-5HacD2HnD
(hAP ac³ LTE6 kit), an  indoor dual band, dual-radio 802.11ac
wireless AP with built-in Mini PCI-E LTE modem, one USB port, five
10/100/1000 Mbps Ethernet ports.

See https://mikrotik.com/product/hap_ac3_lte6_kit for more info.

Specifications:
 - SoC: Qualcomm Atheros IPQ4019
 - RAM: 256 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi internal antennae
   · Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi internal antennae
 - Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port
 - 1x USB Type A port
 - 1x Mini PCI-E port (supporting USB)
 - 1x Mini PCI-E LTE modem (MikroTik R11e-LTE6, Cat.6)

Installation:

Make sure your unit is runnning RouterOS v6 and RouterBOOT v6 (tested on 6.49.6).

0. Export your MikroTik license key (in case you want to use the device with RouterOS later)
1. Boot the initramfs image via TFTP
2. Upload the "openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin" via SCP to the /tmp folder
3. Use sysupgrade to flash the image: sysupgrade -n /tmp/openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin
4. Recovery to factory software is possible via Netinstall:
   https://help.mikrotik.com/docs/display/ROS/Netinstall

Signed-off-by: Csaba Sipos <metro4@freemail.hu>
2022-10-30 23:14:45 +01:00
Florian Eckert
80edacc8a6 target/mxs: replace gpio-mcp23s08 with pinctrl-mcp23s08
The dependency on the kernel module gpio-mcp23s08 is replaced by
pinctrl-mcp23s08-spi and pinctrl-mcp23s08-i2c, as the gpio-mpc23s08 kernel
module no longer exists.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2022-10-30 23:14:45 +01:00
Florian Eckert
29ae20519a kernel: remove CONFIG_GPIO_MCP23S08 from default kernel configs
The kernel config option 'CONFIG_GPIO_MCP23S08' no longer exists.
Therefore, it is removed from the generic kernel configuration for
linux-5.10 and linux-5.15.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2022-10-30 23:14:45 +01:00
Florian Eckert
f938512af6 target/at91: replace gpio-mcp23s08 with pinctrl-mcp23s08-spi update config
Adapt the device package to no longer use the gpio-mcp23s08 but instead
use the pinctrl-mcp23s08-spi. In addition, the kernel configuration was
adapted so that this can be built as a module and does not have to be
integrated directly into the kernel for this target.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2022-10-30 23:14:45 +01:00
Florian Eckert
1dccc6e749 kernel: replace gpio-mcp23s08 with pinctrl-mcp23s08*
The kernel module gpio-mcp23s08 has been replaced by the new
pinctrl-mcp23s08* kernel modules.

There are now 3 kernel modules for this device
- Common module for both I2C and SPI kmod-pinctrl-mcp23s08
- Module for I2C kmod-pinctrl-mcp23s08-i2c
- Module for SPI kmod-pinctrl-mcp23s08-spi

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2022-10-30 23:14:45 +01:00
Roland Barenbrug
cc5d8ae427 ltq-vdsl-vr9-app: extend ubus call to provide DSL statistics
Adding a new method to `ubus call dsl` to retrieve DSL statistics
used to feed the DSL charts (bit allocation, SNR, QLN and HLOG)

Signed-off-by: Roland Barenbrug <roland@treslong.com>
[fix pointer error, clean up]
Signed-off-by: Andre Heider <a.heider@gmail.com>
2022-10-30 23:14:45 +01:00
Roland Barenbrug
5787e0c9fe ltq-vdsl-vr9-app: skip invalid line status values
DSL_G997_LineStatusData_t defines special invalid values, skip these
metrics.

Signed-off-by: Roland Barenbrug <roland@treslong.com>
[split patch]
Signed-off-by: Andre Heider <a.heider@gmail.com>
2022-10-30 23:14:45 +01:00
Shiji Yang
e6769d11f3 scripts: fix missing character '0' issue in linksys image
In the stock firmware of Linksys, there is a '0' after the crc checksum.
Validated on EA6350V3, EA7300 and EA7300V2's stock images.

Fixes: 892d741259 build: add a script for generating Linksys factory images
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-10-30 23:14:45 +01:00
Edward Chow
50f727b773 ath79: add support for Linksys EA4500 v3
Add support for the Linksys EA4500 v3 wireless router

Hardware
--------
SoC:    Qualcomm Atheros QCA9558
RAM:    128M DDR2 (Winbond W971GG6KB-25)
FLASH:  128M SPI-NAND (Spansion S34ML01G100TFI00)
WLAN:   QCA9558 3T3R 802.11 bgn
        QCA9580 3T3R 802.11 an
ETH:    Qualcomm Atheros QCA8337
UART:   115200 8n1, same as ea4500 v2
USB:	1 single USB 2.0 host port
BUTTON: Reset - WPS
LED:    1x system-LED
        LEDs besides the ethernet ports are controlled
        by the ethernet switch

MAC Address:
 use        address(sample 1)    source
 label      94:10:3e:xx:xx:6f   caldata@cal_macaddr
 lan        94:10:3e:xx:xx:6f   $label
 wan        94:10:3e:xx:xx:6f   $label
 WiFi4_2G   94:10:3e:xx:xx:70   caldata@cal_ath9k_soc
 WiFi4_5G   94:10:3e:xx:xx:71   caldata@cal_ath9k_pci

Installation from Serial Console
------------

1. Connect to the serial console. Power up the device and interrupt
   autoboot when prompted

2. Connect a TFTP server reachable at 192.168.1.0/24
   (e.g. 192.168.1.66) to the ethernet port. Serve the OpenWrt
   initramfs image as "openwrt.bin"

3. To test OpenWrt only, go to step 4 and never execute step 5;
   To install, auto_recovery should be disabled first, and boot_part
   should be set to 1 if its current value is not.

   ath> setenv auto_recovery no
   ath> setenv boot_part 1
   ath> saveenv

4. Boot the initramfs image using U-Boot

   ath> setenv serverip 192.168.1.66
   ath> tftpboot 0x84000000 openwrt.bin
   ath> bootm

5. Copy the OpenWrt sysupgrade image to the device using scp and
   install it like a normal upgrade (with no need to keeping config
   since no config from "previous OpenWRT installation" could be kept
   at all)

   # sysupgrade -n /path/to/openwrt/sysupgrade.bin

Note: Like many other routers produced by Linksys, it has a dual
      firmware flash layout, but because I do not know how to handle
      it, I decide to disable it for more usable space. (That is why
      the "auto_recovery" above should be disabled before installing
      OpenWRT.) If someone is interested in generating factory
      firmware image capable to flash from stock firmware, as well as
      restoring the dual firmware layout, commented-out layout for the
      original secondary partitions left in the device tree may be a
      useful hint.

Installation from Web Interface
------------

1. Login to the router via its web interface (default password: admin)

2. Find the firmware update interface under "Connectivity/Basic"

3. Choose the OpenWrt factory image and click "Start"

4. If the router still boots into the stock firmware, it means that
   the OpenWrt factory image has been installed to the secondary
   partitions and failed to boot (since OpenWrt on EA4500 v3 does not
   support dual boot yet), and the router switched back to the stock
   firmware on the primary partitions. You have to install a stock
   firmware (e.g. 3.1.6.172023, downloadable from
   https://www.linksys.com/support-article?articleNum=148385 ) first
   (to the secondary partitions) , and after that, install OpenWrt
   factory image (to the primary partitions). After successful
   installation of OpenWrt, auto_recovery will be automatically
   disabled and router will only boot from the primary partitions.

Signed-off-by: Edward Chow <equu@openmail.cc>
2022-10-30 23:14:45 +01:00
Daniel Golle
84ff6c90dd
base-files: bring back nand_do_upgrade_success
Several Broadcom targets were using the nand_do_upgrade_success
shell function which has been removed by commit e25e6d8e54
("base-files: fix and clean up nand sysupgrade code"). Refactor the
new nand_do_upgrade to bring back nand_do_upgrade_success with the
behavior expected by those users.

Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code")
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-30 20:26:12 +00:00
John Audia
910bdda6af kernel: bump 5.15 to 5.15.76
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:57:25 +01:00
John Audia
af1e3439a8 rockchip: armv8: add CONFIG_ARM64_ERRATUM_1742098
5.15.76 introduces a new symbol that applies Cortex-A72 SoCs so enable it[1].

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.76&id2=v5.15.75

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:55:00 +01:00
John Audia
86ba286766 mvebu: cortexa72: add CONFIG_ARM64_ERRATUM_1742098
5.15.76 introduces a new symbol that applies Cortex-A72 SoCs so enable it[1].

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.76&id2=v5.15.75

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:55:00 +01:00
John Audia
8e7cc06254 kernel: add # CONFIG_ARM64_ERRATUM_1742098
Introduced with 5.15.76[1]

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.76&id2=v5.15.75

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
a34255b795 kernel: bump 5.15 to 5.15.75
Removed upstreamed:
   bcm27xx/patches-5.15/950-0446-drm-vc4-Fix-timings-for-VEC-modes.patch[1]

Manually rebased:
   patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
   bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
   bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
   bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch

All other patches automatically rebased

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.75&id=2810061452f9b748b096ad023d318690ca519aa3

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
a133423c59 kernel: add # CONFIG_ARM64_ERRATUM_2441007 symbol
Introduced with 5.15.75.[1]

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.75&id2=v5.15.74

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
52400e167d kernel: bump 5.10 to 5.10.152
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
dab23d04af layerscape: armv8_64b: add CONFIG_ARM64_ERRATUM_1742098
5.10.152 introduces a new symbol that applies Cortex-A72 SoCs so enable it[1].

https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.10.152&id2=v5.10.151

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
7a27ac605c kernel: bump 5.10 to 5.10.151
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
aa2fa2eb76 kernel: bump 5.10 to 5.10.150
Manually rebased:
  bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch

All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
[Move gro_skip in 680-NET-skip-GRO-for-foreign-MAC-addresses.patch to old position]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-10-30 17:52:42 +01:00
Chukun Pan
641e4f2f04 mediatek: add Xiaomi Redmi Router AX6000 support
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: ESMT F50L1G41LB 128 MB
  RAM: K4A4G165WF-BCWE 512 MB
  Ethernet: 4x 10/100/1000 Mbps
  WiFi1: MT7976GN 2.4GHz ax 4x4
  WiFi2: MT7976AN 5GHz ax 4x4
  Button: Mesh, Reset

Flash instructions:
  1. Gain ssh and serial port access, see the link below:
     https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
  2. Use ssh or serial port to log in to the router, and
     execute the following command:
     nvram set boot_wait=on
     nvram set flag_boot_rootfs=0
     nvram set flag_boot_success=1
     nvram set flag_last_success=1
     nvram set flag_try_sys1_failed=8
     nvram set flag_try_sys2_failed=8
     nvram commit
  3. Set a static ip on the ethernet interface of your computer
     (e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
  4. Download the initramfs image, rename it to initramfs.bin,
     and host it with the tftp server.
  5. Interrupt U-Boot and run these commands:
     setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
     saveenv
     tftpboot initramfs.bin
     bootm
  6. After openwrt boots up, use scp or luci web
     to upload sysupgrade.bin to upgrade.

Revert to stock firmware:
  Restore mtdparts back to default, then use the
  vendor's recovery tool (Windows only).

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-10-30 14:30:22 +00:00
Rodrigo Balerdi
9d1e687da3 base-files: verify nand sysupgrade images
For nand sysupgrade image files having tar/gzip/tgz envelopes, verify
envelope integrity before starting sysupgrade.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2022-10-30 14:29:56 +00:00
Rodrigo Balerdi
9710712120 base-files: accept gzipped nand sysupgrade images
When firmware images only contained compressed kernels and squashfs roots,
uncompressed tar files were a good option. We are now using UBIFS images,
both raw and tarred, as well as ubinized (full UBI partition) images, all
of which benefit greatly from compression.

For example, a raw ubinized backup taken from a running Askey RT4230W REV6
(such full backups can be restored via the LUCI's sysupgrade UI) is over
400 MB, but compresses to less than 10 MB.

This commit adds support for gzipped versions of all file types already
accepted by the nand sysupgrade mechanism, be them raw or tarred.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2022-10-30 14:29:56 +00:00
Rodrigo Balerdi
af34733593 base-files: fix ubinized nand sysupgrade
It has been reported that ubinized nand sysupgrade fails under certain
circumstances, being unable to detach the existing ubi partition due to
volumes within the partition being mounted.

This is an attempt to solve such issues by unmounting and removing
ubiblock devices and unmounting ubi volumes within the target partition
prior to detaching and formatting it.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2022-10-30 14:29:56 +00:00
Rodrigo Balerdi
e25e6d8e54 base-files: fix and clean up nand sysupgrade code
- Never return from 'nand_do_upgrade', not even in case of errors, as that
  would cause execution of sysupgrade code not intended for NAND devices.
- Unify handling of sysupgrade success and failure.
- Detect and report more error conditions.
- Fix outdated/incorrect/unclear comments.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
2022-10-30 14:29:56 +00:00
Olliver Schinagl
f4849c0ab7 realtek: Fix CRC offloading for rtl83xx
In rtl83xx_set_features we set bit 3 to enable, and bit 4 to disable
checksuming. Looking at rtl93xx_set_features we however see that for
both enable and disable the same bit is used (bit 4). This can't be
right, especially as bit 4 for rtl83xx seems to be Collision threshold
occupying 2 bits. Change this to make this more logical.

Fixes: 9e8d62e421 ("realtek: enable CRC offloading")
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-10-29 11:18:04 +02:00
Christian Marangi
5384c9337f
ipq806x: disable ea8500 image by default
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.

Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.

The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-28 01:16:00 +02:00
Christian Marangi
c4a9a67de8
ipq806x: disable ea8500 image by default
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.

Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.

The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-28 01:10:21 +02:00
Rafał Miłecki
ae57770c95 bcm4908: add pending BQL support for bcm4908_enet
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-27 22:34:00 +02:00
Rafał Miłecki
31e4e56654 bcm4908: backport bcm4908_enet fix for NULL dereference
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-27 21:14:02 +02:00
Rafał Miłecki
6a02205a4d bcm4908: optimize Ethernet driver by using build_skb()
This should slightly improve performance thanks to the better cache
usage.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-27 18:59:46 +02:00
Jan Hoffmann
eb456aedfe realtek: use assisted learning on CPU port
L2 learning on the CPU port is currently not consistently configured and
relies on the default configuration of the device. On RTL83xx, it is
disabled for packets transmitted with a TX header, as hardware learning
corrupts the forwarding table otherwise. As a result, unneeded flooding
of traffic for the CPU port can already happen on some devices now. It
is also likely that similar issues exist on RTL93xx, which doesn't have
a field to disable learning in the TX header.

To address this, disable hardware learning for the CPU port globally on
all devices. Instead, enable assisted learning to let DSA write FDB
entries to the switch.

For now, this does not sync local/bridge entries to the switch. However,
support for that was added in Linux 5.14, so the next switch to a newer
kernel version is going to fix this.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-10-26 09:59:38 +02:00
Jan Hoffmann
2088e440b1 realtek: set up L2 table entries properly
Initialize the data structure using memset to avoid the possibility of
writing garbage values to the hardware.

Always set a valid entry type, which should fix writing unicast entries
on RTL930x.

For unicast entries, set the is_static flag to prevent the switch from
aging them out.

Also set the rvid field for unicast entries. This is not strictly
necessary, as the switch fills it in automatically from a non-zero vid.
However, this makes the code consistent with multicast entry setup.

While at it, reorder the statements and fix some style issues (double
space, comma instead of semicolon at end of statement). Also remove the
unneeded priv parameter and debug print for the multicast entry setup
function.

Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-10-26 09:59:24 +02:00
Bob Cantor
80a62a675d
base-files: wifi: for wifi reconf, scan_wifi after network reload
Commit e8b5429609 included an unintended change and we now call
scan_wifi before a network reload.

Restore the original behaviour and call scan_wifi only after a network
reload.

Fixes: e8b5429609 ("base-files: wifi: tidy up the reconf code")
Signed-off-by: Bob Cantor <bobc@confidesk.com>
2022-10-25 09:24:37 +02:00
Bob Cantor
fcfce8f208
base-files: wifi: for wifi up, scan_wifi after network reload
Commit b82cc80713 included an unintended change and we now call
scan_wifi before a network reload.

Restore the original behaviour and call scan_wifi only after a network
reload.

Fixes: b82cc80713 ("base-files: wifi: swap the order of some ubus calls")
Signed-off-by: Bob Cantor <bobc@confidesk.com>
2022-10-25 09:24:27 +02:00
Christian Marangi
a31b598590
realtek: 5.10: refresh kernel patches
Refresh kernel patches for realtek 5.10 kernel

Refreshed patch:
- 300-mips-add-rtl838x-platform.patch

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 04:56:16 +02:00
Davide Fioravanti
8d921167e9
ipq40xx: convert to DSA and enable Netgear Orbi devices
Convert to DSA and enable again Netgear Orbi devices:
 - RBR50
 - RBS50
 - SRR60
 - SRS60

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2022-10-25 02:34:46 +02:00
Christian Marangi
ea63945b25
generic: 5.15: add missing CMDLINE_OVERRIDE patch
This patch was wrongly dropped with the assumption that it was moved to
generic. This wasn't the case and caused the malfunction of the Asrock
G10 router.

Reintroduce it to fix Asrock G10 functionality.

Fixes: 8cc2caed58 ("ipq806x: 5:15: add testing kernel version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:45 +02:00
Christian Marangi
1c514f05ab
ipq806x: 5.15: drop mmc-ddr-1_8v from sdcc1 node
Zyxel NGB6817 is the only router that use mmc for rootfs. Upstream
kernel dtsi have mmc-ddr-1_8v enabled for sddc1. This is wrong as mmc on
ipq806x is supplied by a fixed 3.3v regulator and can't operate at 1.8v.
This cause the sddc1 to malfunction and cause kernel panic.
In old 5.15 version this was disabled but it was put in addition to many
other changes so it was dropped silently. Restore this patch to fix
working condition of such router.

Fixes: 88bf652 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Fixes: #11000
Tested-by: Hendrik Koerner <koerhen@web.de>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:45 +02:00
Christian Marangi
a87b6cda02
ipq806x: 5.15: revert unwanted DSA conversion for ASRock G10
In refreshing DTS to the upstream version an unwanted change slipped in
the commit. The ASRock G10 dts got converted to DSA without any support.

Revert this to swconfig driver to restore normal functionality.

Fixes: 88bf652525 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:45 +02:00
Christian Marangi
dd2515cb53
ipq806x: 5.15: backport qcom_nandc patch for unprotected spare data fix
We currently ignore ret of the nandc partition parser if unprotected
spare data is true. This is the case for ipq806x nand.

Backport patch that fix this error and correctly handle error from
partition parser.

Fixes: ae6a63bc97 ("ipq806x: 5.15: replace nandc patch with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:44 +02:00
Christian Marangi
04a8944178
generic: 5.15: backport smempart parser fixup patch with EPROBE_DEFER error
Backport patch from kernel 5.15 that mute error on EPROBE_DEFER with
smempart parser.

This parser require the smem device to be probed first and currently it
may happen that mtd gets probed before the smem device causing an error
on the smempart parser. This error may be confusing and should be muted.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:44 +02:00
Christian Marangi
221020fda6
generic: 5.15: backport qcom smem patch for reserved-space support
In new kernel version from 5.16, smem node can be declared directly in
the reserved-space node. Upstream ipq806x (and to-be-merged) ipq807x
allign to this new implementation. Backport this patch to kernel 5.15 to
fix support for smem parser for ipq806x target.

Fixes: 88bf652525 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:43 +02:00
Christian Marangi
ffe91ca478
generic: 5.15: move not backport patch to pending dir
Move patch wrongly placed in backport dir to pending dir as they still
didn't got merged upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:48 +02:00
Christian Marangi
2a7bdde29b
generic: 5.15: move MGLRU patches from pending to backport
Move MGLRU patches from pending to backport as they got merged upstream.
These are direct porting from one of the dev so it's better to just move
than trying to backport them again from upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:48 +02:00
Christian Marangi
ccedd7175d
generic: 5.15: move mvebu aardvark patch from pending to backport
Move mvebu aardvark patch from pending to backport as they got merged
upstream.
One additional patch is needed as a later fixup for it.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:47 +02:00